Manufactured From Hardened Carbon Steel With A Dual Material 't' Handle Grip For Comfort And Extra Force. The Ball Drivers Can Be Used At Angles Of Up To 30ã‚â° For Use Where Access Is Restricted And The Shorter Hexagon End Is Ideal For Use When A Greater Tightening Torque Is Required. Long Arm End Is Ball Drive And Short Arm End Plain. Black Oxidised Finish. Manufactured To Iso2936/din911.

Absolute Measuring System With Rs232 Digimatic Output And Four Way Measurement. Large Lcd Display With Cr2032 Battery. Functions: Mm/inch Conversion, On/off, Data Output.resolution: 0.01mm/0.0005".extra Batteries Available - Order Code Edi -904-4000k

Base Mounted Type (flanged)the Straight Line Action Which Gives These Plunger-style Clamps Extremely High Loading Capacities Whilst Maintaining Compactness. These Clamps Also Lock In The Open Position Which Allows A 'pull' To Be Exerted (for Instance, In Use With Foam Moulds). All Models Have Tapped Spindles For Use With Adjustable Spindles.

With Painted Wood Handles. Chrome Plated Lapped And Pressed Steel Ferrules. Long Pure Bristles.

Weldon Shank Adaptorsallows Existing Weldon Shank Side Lock Arbors To Hold Smaller Shank Cutters.

Long Niteoffers Good Mechanical Properties With Nitrile Coating For Protection Against Oil, Grease And Strong Detergents. 640mm Length To Protect The Wearer, And The Sleeve Provides Splash Protection. Comfort Cotton Liner Provides High Levels Of Comfort. Applications: Cleaning And Janitorial, Drainage Works, Oil Filtration.cat Iibs En388 4.1.2.1.

Manufactured From Premium Grade Micrograin Carbide To Give Maximum Strength And Extend Tool Life. Available In Three Sinusoidal Pitch Forms Which Balance Edge Strength With Optimum Metal Removal. Cutters Over 10mm Are Provided With Weldon Flats For Positive Drive During Heavy Cuts. Cutters Conform To Ansi Standards.

Plastic Waste Paper Bins, Ideal For Use In The Office Or Warehouse. Available In Four Colours.capacity: 14 Litre.

Rat 06tan. Lined Rigger Boots Are Tough On The Outside, Soft And Warm On The Inside, Providing Comfort And Safety When Worn All Day, In The Most Challenging Weather Conditions You'll Encounter On-site. Energy Absorbing Heels For Extra Comfort. Fur-lining. 200 Joules Steel Toe Cap Impact Protection. Guards Against Falling Objects And Collisions. Steel Midsole To Prevent Sharp Object Penetration. Ideally Suited To Building Sites And Where Metal Swarf Is Present On Floors. Normally Allows Walking On Hot Surfaces Up To 200ã‚â°c. Resists The Build-up And Conductance Of Static Electricity. Of Most Benefit When Walking On Synthetic Carpets Or Near Electrical Machinery. Dual Density Polyurethane/rubber Soles For Extra Comfort. The Sole Features A Nitrile Rubber Outsole, Resistant To Heat To 300ã‚â° And A Low Density Polyurethane Interlayer, For Increased Comfort And Shock Absorption. Tuffsafe Rigger Boots Are A Type Of Pull-on Safety Boot Used By Tradesmen And Construction Workers Specialising In Heavy Construction Work And Other Types Of Demanding Working Conditions. Tuffsafe Rigger Boots Are The Ideal Safety Footwear For Winter Weather As They Go A Third Of The Way Up The Leg This Keeps Your Feet Dry And The Bottom Of Your Trousers Clean As You Can Tuck Them In The Top Of The Boot.s1p Classified.manufactured To En Iso 20345:2011.

Made From Tough Hard Wearing Plastic. Can Be Free Standing, Or Fixed Onto A Surface. The All Purpose Bullseye Circular Level Will Show Level Of Any Surface In All Directions At Once. Height: 16mm Diameter: 50mm

Adhesive Puttyeconomic Reusable Adhesive Will Hold Papers Or Light Objects To Most Surfaces. Will Not Mark Walls Or Dry Out.size: 70 And 140g.

Zirconium Grade Aluminium-backed High Performance Alternative To Sanding Discs. Have The Advantage Over Depressed Centre Grinding Discs On Light Gauge Sheet Metal Where Surface Finish Is Important. Overlapped Abrasive Strips Slowly Wear Away Revealing Fresh Abrasive, Ensuring The Disc Always Cuts Effectively, Reducing Clogging, Provides Constant Finish Throughout Disc Life. No Backing Pads Needed. Safe To Use At 80m/s On Any Grinder. Tested At 150m/s Nd Approved By The German Grinding Wheel Authority (dsa). Available In Two Grades And With Two Types Of Backing.100mm Dia X 16mm Bore 15,300 Mos (rpm)115mm Dia X 22mm Bore 13,300 Mos (rpm)125mm Dia X 22mm Bore 12,000 Mos (rpm)

Piezo Self Ignition. Uses Standard Butane Lighter Fuel And Is Simple To Refill. Fully Adjustable Tip Temperature Control With A Safety Fuel Cut-off When Cap Is Replaced. Textured Anti-slip Barrel With Built In Stand For Anti Roll. Supplied With Pointed Soldering Tip. Can Be Used With Double Flat, Hot Air, Flame And Hot Knife, Can Also Be Used As A Blow Torch. Supplied Without Fuel. Power Rating: 50wsoldering Temperature: 375ã‚â°crun Time: 60 Minutes Overall Length With Cap: 195mmoverall Length With Soldering Tip: 180mm.

1813 Versatile Caddy Which Will Not Rust, Dent Or Chip. Easy Grip Handle. High Surround Sides.dimensions: 480 X 343 X 221mm.

Low Bloom Low Odour. Medium/high Viscosity. Ideal Where Cosmetic Appearance Is Required. Improved Fixture Strength On Metal And Plastic. Also For Porous Substrates And Acidic Surfaces. Drinking Water Wras Approved.gap Fill: 0.25mm.colour: Clear. Temperature: -40 To +80ã‚â°c.comment: Low Bloom, Low Odour.

For Fine Surface Finishing Of Intricate Contour Surfaces. Used To Manually Remove Small Amounts Of Material And Excels In Tricky Grain Areas Where Hand Planes Would Cause Tear Out. They Will Stand Up To Any Heavy-duty Scraping Task With Minimum Tear Out. For Best Results, These Scrapers Should Be Burnished To A Razor Sharp Edge.

3505for Protection Against Fine Toxic Dusts, Mists And Fumes, Based On Water And Oil. The Full Face Seal Provides A Safe And Secure Fit. The Unique Pleated Filter Technology Reduces Breathing Resistance And The Ventex-valve Minimises Heat Build-up, Making This Mask Extremely Comfortable. The Duramesh Structure Makes The Mask Strong And Durable, Reducing Consumption And Maintaining Shape. Standard: En149:201 + A1:2009 Ffp3 Nr D. Supplied In Packs Of 5. Adjustable Strap. Nose Clip Included.

Sidebent Shears - 3120cphigh Carbon Tool Steel With Chrome Plated Blades With Unique Corrosion Protection On The Inside. Offset Handles With Machined Pivot Screw. Longer Life Is Achieved By Higher Grade Materials And More Finishing Processes.suitable For: Textiles, Synthetic Textiles, Canvas, Rubber, Carpet And Underlay, Felt, Rope, Plastic Film, Plastic And Fine Wire Mesh, Paper And Card Etc.

Gipm-a46: Precision Ground Back Turning Inserts, For External Machining On Swiss Type Automatics.grade: Ic328a Thin Pvd Coated Ticn Layer On A P45-k40 Substrate. Very High Toughness. For Milling, Parting And Grooving Of Steel, Stainless And Alloy Steels At Low To Medium Cutting Speeds And For Unstable Machining Conditions.iso Range - P/m/k: (p25-p40)(m30-m40)iso Range - H/s/n: (s20-s30)grade Or Coating Type: Pvdcoating Layers: Ticn

C-clear Lens Cleaning Towelette Dispenser. Towelette Dispenser Comes Completely Assembled And Ready For Use. Manufactured With Sturdy Corrugated Cardboard Featuring Pull Out Bottom For Easy Dispensing And Built In Tab For Hanging. Holds 100 - Towelette Measures 8-inches Length By 5-inches Width.-individual Pre-moistened Towelettes-anti-fog, Anti-static Formula-sturdy Corrugated Dispenser Features Pull Out Bottom For Easy Dispensing-completely Assembled And Ready For Use-towelette Measures 8-inches Length By 5-inches Width

Ideal For Dry Or Slightly Oily Applications That Require Light Mechanical Protection. The Use Of Spandex Elastics Prevents Risk Of Latex Allergy, While The Silicone-free Glove Reduces Potential Contamination Of The Products. Conforms To En 388 3131.cat Ii

For A Wide Range Of Materials. Keeps Its Edge In Long-run, Intricate Contouring Jobs. Regular Tooth (constant Pitch) Is Recommended For The Cutting Of Solids And Irregular Shapes. Variable Tooth Form Works Best When Machine Conditions Are Not Ideal.

Kevlar Dotted Grip Gloves. Ideal For Heavy-duty Handling Where Enhanced Grip Is Essential. 100% Knitted Heavyweight Kevlar Glove. High Cut And Abrasion Resistance, Even When Wet. Pvc Polka Dots For Greater Gripping Capabilities.colour: Yellow.sizes: 7, 8, 9 And 10.

Fitted Earth Terminals To Provide A Double Earth Facility For Use When Installations Require A High Integrity Protective Connection As Specified Within Bs 7671 Iet Wiring Regulationsã¢â‚¬â�¹

Standard Dimmer Suitable For Tungsten Filament Lighting