|
|
Disc Brake Caliper Guide Pin - Fte Rs0018 Saab 90297771.
Audi Vw Volvo And Saab Brake Caliper Guide Pin. Fits Saab 900 88-93 & 94 Convertible (rear Caliper) 900 94-98 All (front) 9000 All (rear Caliper) (88-98 Turbo Front 90-98 All Front) 9-3 99-02 & 03 Convertible All (front Caliper) 9-5 All (front All) (rear Mid 99-08 From Vin# X3025752 On). 2 Per Caliper.
Manufacturer: Fte
ID: Rs0018
Category: Rear Brakes
SKU: 43156
|
|
|
Power Steering Hose (suction) - Uro Parts 30645081.
Power Steering Suction Hose (resevoir To Pump) For Any S/v 70 99-00 S60 01- Mid 05 (up To Chassis # 430013) V70 01- Mid 05 (factory Code 1 Up To Chassis # 464223 Factory Code 2 Up To Chassis # 463601) Xc70 03- Mid 05 (up To Chassis # 175179) S80 5cyl 04 - Mid 05 (up To Chassis # 392330).
Manufacturer: Uro Parts
ID: 30645081
Category: Steering
SKU: 9357
|
|
|
Timing Belt Tensioner Pulley - Proparts 21432593 Volvo 3517997.
Timing Belt Tensioner Pulley For Any 850 93 (up To Engine #131034) 960 92( Up To Engine # 131034). Original Pn: 6842593
Manufacturer: Proparts
ID: 21432593
Category: Engine Timing
SKU: 39584
|
|
|
Serpentine Belt Tensioner Bolt - Genuine Bmw 11287530315.
Aluminum Torx Bolt For The Mechanical Belt Tensioner. M11x65-al. Aluminum Bolts May Only Be Used Once Then Replaced.
Manufacturer: Genuine Bmw
ID: 11287530315
Category: Other
SKU: 48063
|
|
|
Saab Shifter Bushing Kit - Eeuroparts.com Kit.
1 Kit Per Car. Set Of Two (2) High-performance Shifter Bushings Manufactured Exclusively For Eeuroparts.com. This Bushing Is Created To Very High Tolerances To Completely Take The Slop Out Of Your Shifts. Shifter Bushing For Any 1994-98 Saab 900 1999-02 Saab 9-3 (+ 2003 Convertible) 1986-1998 Saab 9000 And 1999-05 9-5. These Are The Lower Shifter Bushings.
Manufacturer: Eeuroparts.com Kit
Category: Manual Transmission
SKU: 51153
|
|
|
Coilover Kit (adjustable) (w/ Edc) - Dinan R1909131 Bmw.
The Dinan Performance Coilover Kit Utilizes The Factory Electronic Damper Control Shocks And Provides The User With Performance Lowering Springs. Ride Height Is Adjusted Up To 1 Inch Using The Billet Threaded Collars. The Beehive Shaped Front Springs Low Profile Camber Plates And Progressive Bump Stops Allow The 335i To Maintain Stock Suspension Travel While Being Lowered. The Strut Mounts Are Made From 6061-t6 Aluminum And Incorporaate Heavy Duty Rubber And Delran Components For Increased Performance And Quiet Operation. This Kit Allows For Camber Adjustments Between -1.2 And -3.2 Degrees. Lastly Dinan Includes Suspension Packers Which Allow The User To Adjust Bump Stop Clearance. All Of The Components In The Kid Are Compatible With 2.50 Inside Diameter Racing Springs.
Manufacturer: Dinan
ID: R1909131
Category: Rear Suspension
SKU: 164183
|
|
|