|
|
Visegrip Tvg73 3pc Plier Set 10wr6ln 5wr C/w Kitbag.
10wr And 5wr Have Curved Jaws And A Wire Cutter. 6ln Is A Long Nose Straight Jaw With Wire Cutter.set Contents:10wr: O/length: 250mm. Jaw Capacity: 48mm.6ln: O/length: 150mm. Jaw Capacity: 51mm.5wr: O/length: 125mm. Jaw Capacity: 29mm.complete With Kit Bag.
Manufacturer: Visegrip
ID: Tvg73
Category: Hand Tools , gt, Pliers , amp, Grips , gt, Locking Plier Sets
SKU: Vis5581026v
|
|
|
John Guest Speedfit 15mmx25m Speedfit Barrier Pipe Coil.
Manufactured To Bs7291 Parts 1 And 3 Class S And Cs Kite Marked.supplied In 25m Coilspush-fit Solution For Plumbing & Heating Systemsfor Use With Mains Fed And Indirect Cold Water Systems, Vented And Unvented Hot Water Systems, Vented And Sealed Central Heating Systems. Pipes Speedfit Fittings Can Be Used With Copper Pipe To Bs En 1057 And Speedfit Cross-linked Polyethylene (pex) Barrier Pipe To Bs7291.not To Be Used With Gas, Fuel Oil Or Compressed Air Applications. Speedfit Fittings Cannot Be Used On Stainless Steel Pipe. Standards Speedfit Products Are Designed And Manufactured Under A Fully Integrated System Assessed By B.s.i. To Bs En Iso9001. They Are Approved By The Water Regulations Advisory Scheme And Bba. Speedfit 'pem' And 'pkm' Fittings And Speedfit Barrier Pipe Are Kitemarked To Bs7291 Part 1 And 3, Class S. (licence No. Km39767).pipe In Ceilings And Roof Voids Should Be Clipped Every Metre And Should Not Be Fitted Any Closer Than 60mm From The End Of The Fitting. Pipe Should Be Adequately Supported By Pipe Clips To Prevent Undue Stress (side Load) On Fittings.can Only Be Used With Water Or Oil Based Paint, Not Cellulose Based Paints, Paint Thinners Or Strippers, Solder Flux Or Acid-based Descalents Or Aggressive Household Cleaning Products. Speedfit Products, When Used Indoors, Are Not Affected By Sunlight. When Used Outdoors Protect From Ultra Violet Light By Lagging Or Painting.it Is Recommended That All Installations Are Checked Prior To Use To Determine That A Seal Has Been Made.
Manufacturer: John Guest Speedfit
ID: 15bpex-25c
Category: Fluid , amp, Water Control , gt, Water Control , gt, Push-fit Fittings
SKU: Jng2921120k
|
|
|
Kobe Red Line 3/8" X 25ft Nylon Hose.
Solid Brass Couplings With 360ã‚â° Swivel And Spring Protectors Allow Use In Any Direction. Ideal For Use In Awkward Access Areas.ã¢â‚¬ë†recoils To A Fraction Of Its Working Length When Not In Use Leaving The Work Place Clear Of Entanglement Hazards. Extended Length: 7.5m. Pressure Rating: 8.0mm Diameter - 250psi.9.5mm Diameter - 150psi.
Manufacturer: Kobe Red Line
ID: Sa-325
Category: Fluid , amp, Water Control , gt, Hoses , gt, Airline Hoses
SKU: Kbe2801300k
|
|
|
Pyrex Test Tube Medium Wall 16x125 1620/10m (100).
High Quality Test Tubes Designed And Constructed For Optimum Performance. Manufactured From Pyrex Borosilicate Glass Which Gives Superior Performance To Neutral Borosilicate And Soda-lime Glass. Allows Use At High Temperatures. Excellent Resistance To Chemical Attack. Tubes Up To 12mm Dia. Are 1.0mm Wall Thickness, Larger Sizes Are 1.2mm Thick.conforms To Iso 4142.
Manufacturer: Pyrex
ID: 1620/10m
Category: Laboratory Equipment , gt, Laboratory Supplies , gt, Test Tubes
SKU: Prx3877005e
|
|
|
Kennedy Cu20 Soft Jaws (set-3).
To Suit Quick Jaw Change Chucks (berg, Forkardt, Gamet, Kitagawa, Reishauer, Rohm, Schunk And Smw-autoblock). 3 Piece Sets.
Manufacturer: Kennedy
ID: Cu20
Category: Spindle Nose , amp, Workholding , gt, Chucks, Collets , amp, Toolposts , gt, Chucks , gt, Lathe Chuck Jaws
SKU: Ken4905760k
|
|
|
Rexroth Pneumatics Qr1 Series Bulkhead Connector 6mm.
Bulkhead Connectorsqr1-rsm Series Stainless Steel Tube Locking Mechanism And Polymer Body And Release Ring.
Manufacturer: Rexroth Pneumatics
ID: 2121406000
Category: Fluid Power , gt, Pneumatic Fittings , gt, Bulk Head Connector
SKU: Rxr2916650g
|
|
|
Kennedy Mini Pick & Hook Set (4-pce).
Includes Straight Pick, Full Hook, 90ã‚â° Hook And 45ã‚â° Hook. Ideal On Account Of Use On Cotter Pins, Keys, 'o' Rings, Springs And Washers. Hardened And Tempered Chrome Vanadium Steel Shanks With A Knurled Section For Precise Grip. Impact Resistant Square Section Handles For Secure Grip Even When Greasy. Overall Leength: 120 - 130mm (4 3/4ã¢â‚¬ï¿¾ - 5 1/8ã¢â‚¬ï¿¾).
Manufacturer: Kennedy
ID: 602204
Category: Hand Tools , gt, Engineers Tools , gt, Toolroom , amp, Maintenance , gt, Scrapers, Picks , amp, Hooks
SKU: Ken5182900k
|
|
|
Yamaloy Tpmr 110304-pg Insert Grade Qx5020.
Tpmr Turning Inserts 60ã‚â° Triangular Insertinsert Grade Qx5020(iso P10-p35 M10-m30 K10-k30) Cvd Coated.an Excellent General Purpose Grade For Medium Roughing On Steels, Stainless And Cast Irons.chip Breaker: Pg. Application: Med/gash.
Manufacturer: Yamaloy
ID: 1-02-025646
Category: Cutting Tools , gt, Turning , gt, Iso Turning Inserts
SKU: Yml1208742g
|
|
|
Loctite 401 Prism Cyanoacrylate Adhesive 50gm.
Bonds Most Substrates Including Plastic, Rubber, Metal, Card And Wood. Nsf Food Approved.gap Fill: 0.05mm.colour: Clear. Temperature: -40 To +120ã‚â°c.comment: Universal, Low Viscosity.
Manufacturer: Loctite
ID: 142576
Category: Adhesives , amp, Sealants , gt, Instant Adhesives
SKU: Loc7255003f
|
|
|
Loctite 243 Threadlock Adhesive 250ml.
Medium Strength. Best For Oil Tolerance And All Metals. Nsf Food Approved.features:- Tolerates Minor Contaminates.- Ideal For Parts That Need Subsequent Dismantling.comment: General Purpose, Oil Tolerant, High Temperature.
Manufacturer: Loctite
ID: 1335868
Category: Adhesives , amp, Sealants , gt, Retainers , amp, Threadlockers
SKU: Loc7255114e
|
|
|
Kennedy Metric Set Screws, Nuts, Washers Bzp Kit.
Contents:metric: Grade 8.8: M6 X 25, M6 X 40, M8 X 25, M8 X 40, M10 X 25, M10 X 40mm.unf: Grade 's': 1/4 X 3/4, 1/4 X 1, 5/16 X 1, 5/16 X 1 1/4, 3/8 X 1, 3/8 X 1 1/2.unc: Grade 's': 1/4 X 3/4, 1/4 X 1, 5/16 X 1, 5/16 X 1 1/4, 3/8 X 1, 3/8 X 1 1/2.
Manufacturer: Kennedy
ID: 615-411
Category: Fasteners , gt, Fastener Assortments
SKU: Ken6154110k
|
|
|
Durakit Hi-vis S/s Polo Shirt Saturn Yellow Large.
Manufactured Fro M Brightskyn, Breathable Wicking Polyester. Stone Contrast Collar And Shoulder Panels. Double Band 3m Scotchlite Reflective Tape Around Torso And Over Each Shoulder With Three Press Stud Placket. Bsen471 Class 2.
Manufacturer: Durakit
ID: Crrtg9623103c
Category: Personal Protection , amp, Clothing , gt, Clothing , amp, Workwear , gt, Hi Vis Clothing , gt, Hi Vis Shirts
SKU: Rtg9623103c
|
|
|
Iscar Tnmg 160404-tf Insert Grade Ic907.
Tnmg Turning Inserts 60ã‚â° Triangular Insertnegative (0ã‚â°) Relief Angle, Double-sided, Insert For Medium Machining Of Most Materials.insert Grade Ic907iso Range - (p10-p30)(m05-m20)(k15-k30)(h05-h15)(s05-s20)(n05-n20)coating - Pvd Tialn+tin A Tough Sub-micron Substrate, Suitable For Low-to-medium Cutting Speeds.for Machining Of Heat Resistant Alloys, Austenitic Stainless Steel And Hard Steel.chipbreaker : Tf. Application Medium
Manufacturer: Iscar
ID: 5505124
Category: Cutting Tools , gt, Turning , gt, Iso Turning Inserts
SKU: Isc1153241v
|
|
|
Itl Insulated Tools Ltd Aks1 3mm Insulated Allen Key Tool.
Totally Insulated Hexagon Keys - Screwdriver Typehandle Size (mm): 112 X 34overall Length (mm): 263weight (g): 142key Length (mm): 10blade Length (mm): 160
Manufacturer: Itl Insulated Tools Ltd
ID: 02590
Category: Hand Tools , gt, Electrical , gt, Insulated Tools - Hex Keys , amp, Drivers
SKU: Ins6021500a
|
|
|
Guhring 1686 8.00mm Carbide S/s Oil Feed Reamer Hr500d.
The Solid Carbide Hpc Reamer Hr 500 Operates With Highest Cutting Rates And Produces Extremely High-quality Holes. Therefore, It Enables Considerable Savings In Production Costs. In Addition, It Providess Very High Process Reliability. The Special Coolant Supply Of The Hr 500 D Ensures An Optimal Chip Evacuation And An Optimal Cooling.hr 500 Solid Carbide High-performance Reamersproduct Informationright-hand Cuttingextremely Unequal Flute Spacingstraight-flutedstraight Shank Tolerance H6 For Hydraulic Or Shrink Fit Chucks.1685 Series For Blind Holes.1686 Series For Through Holes.
Manufacturer: Guhring
ID: 01686 008.000
Category: Cutting Tools , gt, Reaming , gt, Machine Reamers , gt, Carbide Chucking Reamers
SKU: Guh1837812n
|
|
|
Guhring 5533 4.00mm Carbide Sl B/ N Slot Drill.
Guhring 5533 10mm Micro Grain Carbide Ball Nosed Fire Slot Drills Are Designed For Die Sinking, Copy And Radius Milling Including Plunge Feed.shank Diameter: 10mm.flute Length: 19mm.overall Length: 72mm.number Of Flutes: 2.
Manufacturer: Guhring
ID: 05533 004.000
Category: Cutting Tools , gt, Milling , gt, Slot Drills , gt, Carbide Slot Drills - Short Series
SKU: Gur1612704c
|
|
|
Kennametal Dft 05t308-hp Insert Grade Kcu40.
Dft - Hp Drill Fix Dft Insertshigh Positive Chipbreaker Geometry Preferred On Ductile And Normal Chipping Materials.insert Grade Kcu40 (p25-p40)(m20-m35)(k15-k30)multilayered Tin-tialn-pvd Coating And A Tough Substrate, That Withstands Interruptions And Provides High Wear Resistance For Long Tool Life. Kcu40 Is The First Choice For High Reliability In Most Materials. This Grade Should Be Used At Medium Speeds And High Feeds Due To Sharper Edges. Kcu40 Covers Steel, Stainless Steel, Cast Iron, And High-temperature Alloys For High Toughness Applications Under Certain Conditions.
Manufacturer: Kennametal
ID: 5066013
Category: Cutting Tools , gt, Hole Making , gt, Drilling Inserts
SKU: Kml1133021c
|
|
|
Brauer P600l Push-pull Toggle Clamp.
Features: These Clamps Are Of Exceptionally Robust Construction Featuring Cast And Machined Handles And Bases. Clamps Are Designed With A Low Plunger Height And With The Mechanism Guarded Within The Base To Avoid Finger Traps. Specification: The Bases Of All Models Are Machined S.g. Iron Castings. The Plungers Are Of Steel, And Their Precision Ground Diameter Runs In A Close-tolerance Hole In The Base Casting. Handle Movement 185ã‚â°.all Axles Are Of Hardened Steel And Run In Either The S.g. Iron Of The Handle, Or In The Close-toleranced Holes Of Hardened Parts. All Models Are Supplied With A Steel Set Screw.
Manufacturer: Brauer
ID: P600l
Category: Spindle Nose , amp, Workholding , gt, Workholding , gt, Fixturing , gt, Toggle C1amps
SKU: Bra4101204h
|
|
|
Bosch Gws 22-230 H - 230mm/9" 2200w Angle Grinder - 240v.
Gws22-230h - 230mm/9" 2200w Angle Grinderprofessional Large Angle Grinder, Low Weight For Optimum Handling. Reduced Vibration With Soft Grip For Enhanced Comfort In Use.compliant To En60745-1 & En60745-2-3.disc Sold Separately
Manufacturer: Bosch
ID: 0601882l73
Category: Power Tools , gt, Corded Power Tools , gt, Grinders , gt, Angle Grinders
SKU: Bch2667355r
|
|
|
Ejendals 167 Tegera Fully Lined Cowhide Gloves Size 9.
Flexible Full Grain Cowhide Palm With Soft And Comfortable Polyester Lining And Nylon Backing. The Soft Leather Palm Contribute Increased Flexibility. Fingertips And Index Finger Are Reinforced With Full Grain Cowhide For Better Hand Protection.
Manufacturer: Ejendals
ID: Creje9611676m
Category: Personal Protection , amp, Clothing , gt, Hand , amp, Arm Protection , gt, Gloves , gt, Cold Protection Gloves
SKU: Eje9611676m
|
|
|
Weldspares 40530 10mmx3/8" Bsp Oxy/fuel Gas Economiser.
40530 Allows The Gas Torch To Be Held On The Hooked Arm When Not In Use Which Shuts Off Gas Supply To The Torch. When Unhooked, The Torch Can Be Immediately Re-ignited From The Pilot Light Without Having To Re-adjust The Valves. Can Save Up To 50% Gas Wastage. 3/8" Bsp Fittings.
Manufacturer: Weldspares
ID: Oxy/acet
Category: Welding, Brazing , amp, Soldering , gt, Gas Welding , gt, Gas Welding Accessories , gt, Regulators , amp, Valves
SKU: Ctl8850242h
|
|
|
|
|
|
3m 150mm 212 Stikit Discs Holed P80.
Aluminium Oxide Paper. For General Purpose Sanding. Fre-cut Coating Inhibits Premature Loading To Give A Longer Lasting Product, Particularly In Fine Grades. Features The 3m Stikit Self-adhesive Fastening System To Ensure Sheets Remain Firmly Attached To Stikit Accessories While In Use. All General Purpose Sanding Applications By Hand Or Using Portable Sanding Machines.use On: Wood, Paint/lacquer, Fillers, Metal. Mineral: Aluminium Oxide.backing: C Weight Paper.coating: Open.bond: Resin Over Glue.
ID: 1381
Category: Abrasives , gt, Sanding , gt, Adhesive Backed Discs , amp, Sheets
SKU: Mmm2016380g
|
|
|
Bosch Gam 220 Mf Angle Level.
Gam 220 Mf Angle Finderthis Digital Angle Finder Is Four Tools In One: An Angle Finder, A Cut Calculator, A Protractor And A Level. Four Tools In One: Angle Finder, Mitre Calculator, Protractor And Level Stores Angle Measurements In Memory For Repeated Use Easy-to-read Illuminated, Rotating Flip Display Measures From 0-220ã‚â° Leg Extension - 16 In. Long Manual Angle Finder Leg Lock, To Reposition The Same Angle Easy Field Calibration For Consistent Results Robust Housing, With Ip 54 Protectionmeasurement Range: 0 - 220ã‚â°measurement Accuracy, Angles: ÂⱠ0.1ã‚â°
Manufacturer: Bosch
ID: 601076600
Category: Hand Tools , gt, Building , amp, Construction , gt, Digital Angle Level
SKU: Bch2669071f
|
|
|