High Performance Polyglycol Brake Fluid. Dry Boiling Point 594f(312c). Wet Boiling Point 401f(205c).

Inner Tie Rod Assembly For Any 850 Model And C7 098-03 Marked 4 (trw P/s Rack) S/v 70 98-00 (x-country Through Vin # 549830) Marked 4 (trw Rack). #4 Is Located On The Production Plate On The Drivers Side Wheel Well(under The Hood). On The 5th Line Of The Plate The Last Digit (section To The Right Of The Divider) Is The Steering Gear Code. It Is Either 4 Or 5

Bulb Failure Relay For Any 86-93 240 740 B230 86-92 740 Td 86 740 16v All 760 V6 86-87 760t 85-87 780 V6 87 780t 87 940 B230 91-95 940 16v All 960 92-94.

Fits Your 1.8l & 1.9l E36. This Complete Clutch Kit Converts Your Current Dual Mass Flywheel To A Standard Flywheel To A Standard Clutch Flywheel And Press Plate Setup. This Significantly Reduces Your Cost And Simplifies You Future Clutch Disc Replacements. Perfect For Light Racing Applications Where Non-standard Clutch Friction Discs And Pressure Plates May Be Required.

Vw / Audi Specific Automatic Transmission Fluid. Please See Manual For The Correct Fluid For Your Vehicle.

Clutch Kit For Any 98 900 Turbo(98 Only!) And 99-02 9-3 (exc Viggen). 2 Piece Kit With Pressure Plate And Clutch Disc..

H&r Camber Plates Are Cnc Machined From Billet Aluminum And Then Anodized And Include Stainless Steel Hardware To Protect Against Corrosion. These Are Compatible With Factory Or Aftermarket Struts. Adjustment Range Is +1.0 Degrees To -2.5 Degrees. The Adjustment Range Is Also Dependent On Ride Height. Lowering The Ride Height Of A Vehicle Naturally Increases Negative Camber Which Will Lead To Accelerated Tire Wear On The Inside Edge. These Camber Plates Will Allow Camber Adjustment Of The Front Wheels To Remove Some Of This Camber For Better Handling And To Prolong The Life Of The Tires.

To Be Used On A T5 Conversion Only Because It Replaces The Deleted Mass Air Flow Sensor. The T5 System Uses A Manifold Absolute Pressure Sensor (map) In Place Of A Mass Air Flow Sensor.

Our In-house Designed Big Pinion Housing Allows You To Run The Larger Size Rear Bearing That Saab Introduced In All 89+ Transmissions For Added Longevity And Load Capacity. The Housing Is Also Made From 7xxx Series Billet Aluminum For Superior Strength Over Cast Aluminum Or Steel Housings Previously Used By Saab.

Warm-up Thermostat To Throttle Body Connection Water Hose. 1 Per Car.

Front Brake Hose For Any 700 900 850 960 92-94 S/v 70 98-00 (11 Rotors) C70 98-03 (11 Rotors)

Outside Air Temperature Sensor For Any 94-98 900 9000 90-98 All.

Rear Oxygen Sensor For Any 03-05 Xc90 T-6. 1 Per Car.

Exhaust Hanger Mount For Any 850 S/v/c 70 98-00. 1 Per Car.

Parking Brake Hardware. Includes Shoe Locking Pins And Return Springs. 1 Kit Per Car.

Alternator Water Pump And Power Steering Serpentine Drive Belt. 1 Per Car. 6pk 1548 Size.

Drivers Side Front Inner Fender Liner (rear Lower Position).

Rear Coil Spring Pad (lower Position) For Any 9-3 Sedan 03-05 (4d Cv) 06-11 (4d 5d Cv). 2 Per Car.

Front Swaybar Bushing Cap For Any 9-3 Sedan 03-05 Convertible 03-05. 2 Per Car.

Nut For Heat Insulation And Sound Insulation Air Ducting Underfloor Coating And Body Reinforcement.

Head Gasket For Any 99-02 Viggen 00-02(and 03 Conv) 9-3 9-5 4cyl All.

O-ring For Intake Manifold Angle Connector On Bmws With N51 And N52 Engines

Window Regulator - Rear Driver Side (without Motor)

Turnsignal Light - Front Passenger Side (amber) (capa)

Engine Coolant Hose Assembly - Lower (w/ Thermostat)